Availability Monitoring Events
Availability Monitoring Events
AccelOps generates the following events related to availability monitoring
Ping Stat Monitoring
Synthetic Monitoring Success Synthetic Monitoring Failure
| Name | Id | Type | Description |
| Event Type | eventType | string | Event type set to PH_DEV_MON_SYS_PING_STAT |
| Event
Severity |
eventSeverity | uint16 | Set to 1. In general, a number between 0 (lowest severity) and 10 (highest severity) |
| Event
Severity Category |
eventSeverityCat | string | Set to Low. IN general, takes the values Low, Medium and High. Event Severities 0-4 are mapped to
Low, 5-8 are mapped to Medium and 9-10 are mapped to High |
| Event
Receive Time |
phRecvTime | Date | Time at which AccelOps generated this event |
| Reporting IP | reptDevIpAddr | Date | IP address of device reporting this event. In this case set to the device reporting the utilization (same as
Host name attribute) |
| Relaying IP | relayDevIpAddr | Date | IP address of device relaying this event from the source to AccelOps. In general it could be a syslog-ng IP address but in this, since AccelOps talks to the device directly, Relaying IP is set to AccelOps IP Address. |
| Raw Event
Log |
rawEventMsg | string | Raw event containing all attributes in comma separated “[Attribute] = value” format. |
| Host name | hostName | string | Host name (as in AccelOps CMDB) of the device whose CPU utilization is being reported |
| Host IP
Address |
hostIpAddr | IP | Access IP (as in AccelOps CMDB) of the device whose CPU utilization is being reported |
| Avg Round
Trip Time |
avgDurationMSec | uint32 | Average Round trip time from the ping tests done during this interval |
| Max Round
Trip Time |
maxDurationMSec | uint32 | Max Round trip time from the ping tests done during this interval |
| Min Round
Trip Time |
minDurationMSec | uint32 | Min Round trip time from the ping tests done during this interval |
| Packet Loss
Pct |
pktLossPct | double | Packet loss percentage from the ping tests done during this interval |
| System
Down Time |
sysDownTime | uint32 | Amount of time during this polling interval that there was 100% ping loss |
| System
Degraded Time |
sysDegradedTime | uint32 | Amount of time during this polling interval that there was 50%+ ping loss |
| Poll Interval | pollIntv | uint32 | Polling interval in seconds |
Synthetic Transaction Monitoring Success
Event Type: PH_DEV_MON_EUM_SUCCESS
Description: Successful Synthetic transaction monitoring test Source: All Key Attributes:
| Name | Id | Type | Description |
| Event Type | eventType | string | Event type set to PH_DEV_MON_SYS_EUM_SUCCESS |
| Event Severity | eventSeverity | uint16 | Set to 1. In general, a number between 0 (lowest severity) and 10 (highest severity) |
| Event Severity
Category |
eventSeverityCat | string | Set to Low. IN general, takes the values Low, Medium and High. Event Severities 0-4 are mapped to Low, 5-8 are mapped to Medium and 9-10 are mapped to High |
| Event Receive
Time |
phRecvTime | Date | Time at which AccelOps generated this event |
| Reporting IP | reptDevIpAddr | Date | IP address of device reporting this event. In this case set to the device reporting the utilization (same as Host name attribute) |
| Relaying IP | relayDevIpAddr | Date | IP address of device relaying this event from the source to AccelOps. In general it could be a syslog-ng IP address but in this, since AccelOps talks to the device directly, Relaying IP is set to AccelOps IP Address. |
| Raw Event Log | rawEventMsg | string | Raw event containing all attributes in comma separated “[Attribute] = value” format. |
| Host name | hostName | string | Host name (as in AccelOps CMDB) of the device whose CPU utilization is being reported |
| Host IP Address | hostIpAddr | IP | Access IP (as in AccelOps CMDB) of the device whose CPU utilization is being reported |
| Synthetic
Transaction Monitor Name |
endUserMonitorName | string | Name of the Synthetic Transaction Monitor |
| Synthetic
Transaction Monitor Step |
endUserMonitorStep | string | Particular step of the Synthetic Transaction Monitor, in case the transaction monitor involves multiple steps. |
| Application
Protocol |
appTransportProto | string | Application protocol such as HTTP |
| Application Port | appPort | string | Port number such as 443 |
| Application
Response Time |
appResponseTimeMSec | uint32 | Synthetic transaction response time (ms) |
| Poll Interval | pollIntv | uint32 | Polling interval in seconds |
Synthetic Transaction Monitoring Failure
Event Type: PH_DEV_MON_EUM_FAIL
Description: Failed Synthetic transaction monitoring test Source: All Key Attributes:
| Name | Id | Type | Description |
| Event Type | eventType | string | Event type set to PH_DEV_MON_SYS_EUM_SUCCESS |
| Event Severity | eventSeverity | uint16 | Set to 1. In general, a number between 0 (lowest severity) and 10 (highest severity) |
| Event Severity
Category |
eventSeverityCat | string | Set to Low. IN general, takes the values Low, Medium and High. Event Severities 0-4 are mapped to Low, 5-8 are mapped to Medium and 9-10 are mapped to High |
| Event Receive
Time |
phRecvTime | Date | Time at which AccelOps generated this event |
| Reporting IP | reptDevIpAddr | Date | IP address of device reporting this event. In this case set to the device reporting the utilization (same as Host name attribute) |
| Relaying IP | relayDevIpAddr | Date | IP address of device relaying this event from the source to AccelOps. In general it could be a syslog-ng IP address but in this, since AccelOps talks to the device directly, Relaying IP is set to AccelOps IP Address. |
| Raw Event Log | rawEventMsg | string | Raw event containing all attributes in comma separated “[Attribute] = value” format. |
| Host name | hostName | string | Host name (as in AccelOps CMDB) of the device whose CPU utilization is being reported |
| Host IP Address | hostIpAddr | IP | Access IP (as in AccelOps CMDB) of the device whose CPU utilization is being reported |
| Synthetic
Transaction Monitor Name |
endUserMonitorName | string | Name of the Synthetic Transaction Monitor test |
| Synthetic
Transaction Monitor Step |
endUserMonitorStep | string | Particular step of the Synthetic Transaction Monitor, in case the transaction monitor involves multiple steps. |
| Application
Protocol |
appTransportProto | string | Application protocol such as HTTP |
| Application Port | appPort | string | Port number such as 443 |
| Reason for Error | errReason | uint32 | Reason for failed Synthetic Transaction Monitor test |
| Poll Interval | pollIntv | uint32 | Polling interval in seconds |