What is a Firewall?
The term firewall originally referred to a wall intended to confine a fire or potential fire within a building. Later uses refer to similar structures, such as the metal sheet separating the engine compartment of a vehicle or aircraft from the passenger compartment.
A firewall can either be software-based or hardware-based and is used to help keep a network secure. Its primary objective is to control the incoming and outgoing network traffic by analyzing the data packets and determining whether it should be allowed through or not, based on a predetermined rule set. A network’s firewall builds a What is a Firewall?
bridge between an internal network that is assumed to be secure and trusted, and another network, usually an external (inter)network, such as the Internet, that is not assumed to be secure and trusted.
Network Layer or Packet Filter Firewalls
Stateless Firewalls
Stateless firewalls are the oldest form of these firewalls. They are faster and simple in design requiring less memory because they process each packet individually and don’t require the resources necessary to hold onto packets like stateful firewalls. Stateful firewalls inspect each packet individually and check to see if it matches a predetermined set of rules. According to the matching rule the packet is either be allowed, dropped or rejected. In the case of a rejection an error message is sent to the source of the traffic. Each packet is inspected in isolation and information is only gathered from the packet itself. Simply put, if the packets were not specifically allowed according to the list of rules held by the firewall they were not getting through.
Stateful Firewalls
Stateful firewalls retain packets in memory so that they can maintain context about active sessions and make judgments about the state of an incoming packet’s connection. This enables Stateful firewalls to determine if a packet is the start of a new connection, a part of an existing connection, or not part of any connection. If a packet is part of an existing connection based on comparison with the firewall’s state table, it will be allowed to pass without further processing. If a packet does not match an existing connection, it will be evaluated according to the rules set for new connections. Predetermined rules are used in the same way as a stateless firewall but they can now work with the additional criteria of the state of the connection to the firewall.
Best Practices Tip for improving performance:
Blocking the packets in a denied session can take more cpu processing resources than passing the traffic through. By putting denied sessions in the session table, they can be kept track of in the same way that allowed session are so that the FortiGate unit does not have to redetermine whether or not to deny all of the packets of a session individually. If the session is denied all packets of that session are also denied. In order to configure this you will need to use 2 CLI commands
config system setting
set ses-denied-traffic enable
set block-session-timer <integer 1 – 300> (this determines in seconds how long, in seconds, the session is kept in the table) end
Application Layer Firewalls
Application layer filtering is yet another approach and as the name implies it works primarily on the Application Layer of the OSI Model.
Application Layer Firewalls actually, for lack of a better term, understand certain applications and protocols. Examples would be FTP, DNS and HTTP. This form of filtration is able to check to see if the packets are actually behaving incorrectly or if the packets have been incorrectly formatted for the protocol that is indicated. This
What is a Firewall?
process also allows for the use of deep packet inspection and the sharing of functionality with Intrusion Prevention Systems (IPS).
Application-layer firewalls work on the application level of the TCP/IP stack (i.e., all browser traffic, or all telnet or ftp traffic), and may intercept all packets traveling to or from an application. They block other packets (usually dropping them without acknowledgment to the sender). Application firewalls work much like a packet filter but application filters apply filtering rules (allow/block) on a per process basis instead of filtering connections on a per port basis.
On inspecting all packets for improper content, firewalls can restrict or prevent outright the spread of networked computer worms and trojans. The additional inspection criteria can add extra latency to the forwarding of packets to their destination.
Proxy Servers
A proxy server is an appliance or application that acts as an intermediary for communicating between computers. A computer has a request for information. The packets are sent to the designated resource but before they can get there they are blocked by the proxy server saying that it will take the request and pass it on. The Proxy Server processes the request and if it is valid it passes onto the designated computer. The designated computer gets the packet and processes the request, sending the answer back to the proxy server. The proxy server sends the information back to the originating computer. It’s all a little like a situation with two people who refuse to talk directly with each other using someone else to take messages back and forth.
From a security stand point a Proxy Server can serve a few purposes:
- Protects the anonymity of the originating computer l The two computers never deal directly with each other l Packets that are not configured to be forwarded are dropped before reaching the destination computer. l If malicious code is sent it will affect the Proxy server with out affecting the originating or sending computer.
Proxies can perform a number of roles including:
- Content Filtering l Caching l DNS proxy
- Bypassing Filters and Censorship l Logging and eavesdropping l Gateways to private networks l Accessing service anonymously
UTM/ NGFW
Unified Threat Management and Next Generation Firewall are terms originally coined by market research firms and refer to the concept of a comprehensive security solution provided in a single package. It is basically combining of what used to be accomplished by a number of different security technologies all under a single umbrella or in this case, a single device. On the FortiGate firewall this is achieved by the use of Security Profiles and optimized hardware.
In effect it is going from a previous style of firewall that included among its features:
- Gateway Network Firewall l Routing
FortiGate Modes
- VPN
To a more complete system that includes:
- Gateway Network Firewall l Routing
- VPN
- Traffic Optimization l Proxy Services l Content Filtering l Application Control l Intrusion Protection l Denial of Service Attack Protection l Anti-virus l Anti-spam l Data Leak Prevention l Endpoint Control of Security Applications l Load Balancing l WiFi Access Management l Authentication Integration into Gateway Security l Logging l Reporting
Advantages of using Security Profiles
l Avoidance of multiple installations. l Hardware requirements are fewer. l Fewer hardware maintenance requirements. l Less space required. l Compatibility – multiple installations of products increase the probability of incompatibility between systems. l Easier support and management. l There is only one product to learn therefore a reduced requirement of technical knowledge. l Only a single vendor so there are fewer support contracts and Service Level Agreements. l Easier to incorporated into existing security architecture. l Plug and play architecture. l Web based GUI for administration.