Configuring HA for virtual clustering
If your cluster uses VDOMs, you are configuring virtual clustering. Most virtual cluster HA options are the same as normal HA options. However, virtual clusters include VDOM partitioning options. Other differences between configuration options for regular HA and for virtual clustering HA are described below.
To configure HA options for a cluster with VDOMs enabled:
- Log into the global web-based manager and go to System > HA.
- From the CLI, log into the Global Configuration:
The following example shows how to configure active-active virtual clustering:
config global config system ha
set mode a-a
set group-name vexample1.com set password vHA_pass_1
end end
The following example shows how to configure active-passive virtual clustering:
config global config system ha
set mode a-p
set group-name vexample1.com set password vHA_pass_1
end end
The following example shows how to configure VDOM partitioning for virtual clustering. In the example, the FortiGate unit is configured with three VDOMs (domain_1, domain_2, and domain_3) in addition to the root VDOM. The example shows how to set up a basic HA configuration that sets the device priority of virtual cluster 1 to 200. The example also shows how to enable vcluster2, how to set the device priority of virtual cluster 2 to 100 and how to add the virtual domains domain_2 and domain_3 to virtual cluster 2.
When you enable multiple VDOMs, vcluster2 is enabled by default. Even so the command to enable vcluster2 is included in this example in case for some reason it has been disabled. When vcluster2 is enabled, override is also enabled.
The result of this configuration would be that the cluster unit that you are logged into becomes the primary unit for virtual cluster 1. This cluster unit processes all traffic for the root and domain_1 virtual domains.
config global config system ha
set mode a-p
set group-name vexample1.com set password vHA_pass_1
set priority 200
set vcluster2 enable config secondary-vcluster
set vdom domain_2 domain_3 set priority 100
end end
end
The following example shows how to use the execute ha manage command to change the device priorities for virtual cluster 1 and virtual cluster 2 for the other unit in the cluster. The commands set the device priority of virtual cluster 1 to 100 and virtual cluster 2 to 200.
The result of this configuration would be that the other cluster unit becomes the primary unit for virtual cluster 2. This other cluster unit would process all traffic for the domain_2 and domain_3 virtual domains.
config global
execute ha manage 1 config system ha
set priority 100
set vcluster2 enable config secondary-vcluster
set priority 200 end
end end
end
Example virtual clustering with two VDOMs and VDOM partitioning
This section describes how to configure the example virtual clustering configuration shown below. This configuration includes two virtual domains, root and Eng_vdm and includes VDOM partitioning that sends all root VDOM traffic to FGT_ha_1 and all Eng_vdom VDOM traffic to FGT_ha_2. The traffic from the internal network and the engineering network is distributed between the two FortiGate units in the virtual cluster. If one of the cluster units fails, the remaining unit will process traffic for both VDOMs.
The procedures in this example describe some of many possible sequences of steps for configuring virtual clustering. For simplicity many of these procedures assume that you are starting with new FortiGate units set to the factory default configuration. However, this is not a requirement for a successful HA deployment. FortiGate HA is flexible enough to support a successful configuration from many different starting points.
Example virtual clustering network topology
The following figure shows a typical FortiGate HA virtual cluster consisting of two FortiGate units (FGT_ha_1 and FGT_ha_2) connected to and internal network, an engineering network and the Internet. To simplify the diagram the heartbeat connections are not shown.
The traffic from the internal network is processed by the root VDOM, which includes the port1 and port2 interfaces. The traffic from the engineering network is processed by the Eng_vdm VDOM, which includes the port5 and port6 interfaces. VDOM partitioning is configured so that all traffic from the internal network is processed by FGT_ha_1 and all traffic from the engineering network is processed by FGT_ha_2.
This virtual cluster uses the default FortiGate heartbeat interfaces (port3 and port4).
Example virtual cluster showing VDOM partitioning
General configuration steps
The section includes web-based manager and CLI procedures. These procedures assume that the FortiGate units are running the same FortiOS firmware build and are set to the factory default configuration.
General configuration steps
1. Apply licenses to the FortiGate units to become the cluster.
2. Configure the FortiGate units for HA operation.
- Optionally change each unit’s host name.
- Configure HA.
2. Connect the cluster to the network.
3. Configure VDOM settings for the cluster:
- Enable multiple VDOMs.
- Add the Eng_vdm VDOM.
- Add port5 and port6 to the Eng_vdom.
4. Configure VDOM partitioning.
5. Confirm that the cluster units are operating as a virtual cluster and add basic configuration settings to the cluster.
- View cluster status from the web-based manager or CLI.
- Add a password for the admin administrative account.
- Change the IP addresses and netmasks of the port1, port2, port5, and port6 interfaces.
- Add a default routes to each VDOM.