IPS concepts
The FortiGate Intrusion Protection System (IPS) protects your network from outside attacks. Your FortiGate unit has two techniques to deal with these attacks: anomaly- and signature-based defense.
Anomaly–based defense
Anomaly-based defense is used when network traffic itself is used as a weapon. A host can be flooded with far more traffic than it can handle, making the host inaccessible. The most common example is the denial of service (DoS) attack, in which an attacker directs a large number of computers to attempt normal access of the target system. If enough access attempts are made, the target is overwhelmed and unable to service genuine users. The attacker does not gain access to the target system, but it is not accessible to anyone else.
The FortiGate DoS feature will block traffic above a certain threshold from the attacker and allow connections from other legitimate users. The DoS policy configuration can be found in the Firewall Handbook.
Access control lists in DoS Policies
This feature allows you to define a list of IPs/subnets/ranges in a DoS policy, and block those IPs from sending any traffic, by way of an ACL (access control list). The ACL looks similar to a firewall policy, but only checks source IP, destination IP, destination port, and protocol.
Syntax
config firewall acl edit 1
set interface “port1”
set srcaddr “google-drive” set dstaddr “all”
set service “ALL” next
end
Signature-based defense
Signature-based defense is used against known attacks or vulnerability exploits. These often involve an attacker attempting to gain access to your network. The attacker must communicate with the host in an attempt to gain access and this communication will include particular commands or sequences of commands and variables. The IPS signatures include these command sequences, allowing the FortiGate unit to detect and stop the attack.
Signatures
IPS signatures are the basis of signature-based intrusion protection. Every attack can be reduced to a particular string of commands or a sequence of commands and variables. Signatures include this information so your FortiGate unit knows what to look for in network traffic.
Signatures also include characteristics about the attack they describe. These characteristics include the network protocol in which the attack will appear, the vulnerable operating system, and the vulnerable application.
To view the complete list of signatures, go to Security Profiles > Intrusion Protection, and select View IPS Signatures. This will include the predefined signatures and any custom signatures that you may have created.
Protocol decoders
Before examining network traffic for attacks, the IPS engine uses protocol decoders to identify each protocol appearing in the traffic. Attacks are protocol-specific, so your FortiGate unit conserves resources by looking for attacks only in the protocols used to transmit them. For example, the FortiGate unit will only examine HTTP traffic for the presence of a signature describing an HTTP attack.
IPS engine
Once the protocol decoders separate the network traffic by protocol, the IPS engine examines the network traffic for the attack signatures.
IPS sensors
The IPS engine does not examine network traffic for all signatures. You must first create an IPS sensor and specify which signatures are included. Add signatures to sensors individually using signature entries, or in groups using IPS filters.
To view the IPS sensors, go to Security Profiles > Intrusion Protection.
There is a disabled group of industrial signatures. This category is disabled by default, however it can be applied through use of the CLI command below. Note that none will mean no signatures are excluded, and that industrial will exclude all industrial signatures.
CLI Syntax
config ips global
set exclude-signatures [none | industrial]
end
IPS filters
IPS sensors contain one or more IPS filters. A filter is a collection of signature attributes that you specify. The signatures that have all of the attributes specified in a filter are included in the IPS filter.
For example, if your FortiGate unit protects a Linux server running the Apache web server software, you could create a new filter to protect it. By setting OS to Linux, and Application to Apache, the filter will include only the signatures that apply to both Linux and Apache. If you wanted to scan for all the Linux signatures and all the Apache signatures, you would create two filters, one for each.
To view the filters in an IPS sensor, go to Security Profiles > Intrusion Protection, select the IPS sensor containing the filters you want to view, and select Edit.
Custom/predefined signature entries
Signature entries allow you to add an individual custom or predefined IPS signature. If you need only one signature, adding a signature entry to an IPS sensor is the easiest way. Signature entries are also the only way to include custom signatures in an IPS sensor.
Another use for signature entries are to change the settings of individual signatures that are already included in a filter within the same IPS sensor. Add a signature entry with the required settings above the filter, and the signature entry will take priority.
Policies
To use an IPS sensor, you must select it in a security policy or an interface policy. An IPS sensor that it not selected in a policy will have no effect on network traffic.
IPS is most often configured as part of a security policy. Unless stated otherwise, discussion of IPS sensor use will be in regards to firewall policies in this document.
Session timers for IPS sessions
A session-ttl (time to live) timer for IPS sessions is available to reduce synchronization problems between the FortiOS Kernel and IPS, and to reduce IPS memory usage. The timeout values can be customized.